Here down the page yow will discover a good deal of helpful news about A Step-by-Step Guide to Installing a Bathtub.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough task. If the old tub is conveniently easily accessible, the job can move easily; if you need to open up a wall surface to get rid of the old tub as well as place the new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This post will certainly aid you set up a new bathtub in your washroom if you have actually already bought a brand-new tub as well as do not require to change the setup of your previous water system pipelines.
Your tools and also material checklist need to consist of the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing taps can be rather troublesome as a result of the limited gain access to that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in place between the tap as well as the sink. Protect the faucet in position with the supplier given backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap adapters. The previous kind ought to be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Making use of both wooden boards under its feet, position the tub in the required setting. The wooden boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the bath tub till the level checks out level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water as well as check all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and likewise examine the overflow outlet and also the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last setting.
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to break a rigid seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in issues with dampness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and also cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads on A Step-by-Step Guide to Installing a Bathtub, I think sharing that article was really helpful. Are you aware of somebody who is sincerely interested in the subject? Do not hesitate to promote it. Thank you for your time. Come back soon.
No more waits!